Skip to main content

Wallpaper · 13 min read · 5 May 2026

How to prepare walls for wallpaper: stripping, glue, cracks and damp

How walls are prepared for wallpaper in UAE homes: removing old wallpaper and glue, papering over paint, cracks, putty, textured walls, damp, plaster and primer.

By Ali Haider Basra, Founder, Al Tareeq Decor · Contact our workshop

Bedroom walls in a grey concrete-effect finish around a white fluted headboard panel with a lit edge, above a grey channel-tufted bed and a white bedside table

Key takeaways

  • Most wallpaper faults start in the wall: cracks, loose paint, old paper, texture or damp.
  • Strippable papers peel off dry; others need scoring, warm water and patience, rarely a steamer.
  • Wash off every trace of old glue and let the wall dry for a day before priming.
  • Paper can go over sound, sanded paint, but not over old wallpaper or tiles; textured walls need a skim or lining paper.
  • Fix damp at its source and let new plaster dry fully; then prime or size as the paper asks.
On this page

The wall underneath decides how long wallpaper lasts

Wallpaper is a thin skin, and it copies whatever lies beneath it. A ridge of dried filler becomes a line across the pattern, a hairline crack becomes a shadow, a patch of chalky paint lets a seam lift, and a damp corner turns into a bubble and then a stain. None of those faults is in the paper. They were on the wall before it went up, and they are the reason a well-chosen paper can look tired within a season.

Good preparation is mostly invisible once the room is finished, which is why it is the step most often rushed. The six stages in the drawing below are the ones every wall goes through with us, though some walls need only a light pass at each. The rest of this guide takes them one at a time, including the questions people search most: how to take old wallpaper off, how to clean off the glue, and whether paper can go straight over paint.

Six stages of preparing a wall for wallpaperSix panels showing the same slice of wall in section: first with flaking paint, a crack and a damp spot, then stripped with the crack still open, then the crack filled, then a thin skim coat sanded flat, then a primer line, and finally a sheet of wallpaper over the sound surfaceGetting a wall ready for wallpaperThe same slice of wall in section at each stage. Not to scale.InspectCracks, damp, loose paintStrip and scrapeOld paper and flakes offFillCracks opened and filledSkim and sandOne flat, even facePrime or sizeEven suction for pasteHangPaper on a sound wall123456
  1. 1. Inspect: look for cracks, damp, loose paint and old paper
  2. 2. Strip and scrape: old wallpaper and flaking paint come off
  3. 3. Fill: cracks are opened slightly, filled and left to harden
  4. 4. Skim and sand: uneven or textured walls get one flat face
  5. 5. Prime or size: the surface takes the paste evenly
  6. 6. Hang: the paper goes onto a clean, dry, sound wall
Our drawing of the six preparation stages on one slice of wall. Not every wall needs every stage in full; the inspection decides.

Inspect the wall in raking light

Look at each wall with the furniture pulled away and a torch held flat against the surface, so its beam skims across the plaster. Raking light like this shows every bump, dent and patch that ordinary room light hides, and it shows them roughly the way low evening sun will show them through a finished paper. Run a hand over the wall as well: chalky paint leaves powder on the palm, and loose paint sounds hollow when tapped.

Pay special attention to the places where trouble starts in UAE homes: the wall beside a split AC unit and under its drain pipe, any wall shared with a bathroom or kitchen, the area around window frames, and outside walls that the AC cools hard on one side while the sun heats the other. A stain, a soft spot or a tidemark on any of these means moisture, and it has to be traced before anything else happens. Note sockets and switches too, and anything that is going to move, because that is far easier before the paper goes up.

  • Cracks: fine surface lines, or wider ones running from the corners of doors and windows
  • Paint: sound and firm, or flaking and powdery when rubbed
  • Old wallpaper, and whether its seams are lifting
  • Stains, soft plaster or a musty smell near wet rooms, windows and AC units
  • Texture: a smooth plaster face or a sprayed or rolled texture
  • Sockets, switches, frames and skirting the paper must be cut around

How to remove wallpaper from a wall

Start by finding out what kind of paper is up. Lift a corner at a seam with a fingernail or a plastic scraper and pull slowly at a low angle. Modern strippable papers, many non-wovens among them, come away in whole sheets, dry. Vinyls often split: the printed face peels off and the backing stays on the wall. If that backing is firmly stuck, flat and free of tears it can sometimes be left as a lining for the next paper; if it lifts or bubbles anywhere, it comes off too.

Paper that stays put needs water. This Old House, the American home-renovation programme, sets out the method in its stripping guide. Switch off the power to the room's sockets and switches, remove their faceplates and tape over the openings, and lay plastic sheeting along the skirting. Score the surface lightly with a scoring tool so water can get behind it, then spray it with hot water mixed with a wallpaper stripper and keep it wet; the paper usually starts to bubble within a few minutes. Work a putty knife behind the edge of a sheet and pull it down, soaking again wherever it resists. The same job is set out step by step in how to remove old wallpaper and glue.

Many people search for how to remove wallpaper without a steamer, and in most rooms a steamer is not needed: a garden pump sprayer or spray bottle of warm water, patience and repeated soaking do the same job with less risk. Go gently on gypsum board, the plasterboard used for most partitions and ceilings. Its face is paper, and over-wetting or deep scoring can tear it, leaving a wall that needs skimming. Steam earns its place mainly on several layers of old paper, or on painted-over paper that water cannot get through.

A New Zealand hardware chain strips a wall step by step: scoring, soaking, scraping the wet paper away, then cleaning and readying the surface. No special products are needed, which makes it easy to follow anywhere. Video by Mitre 10 New Zealand on YouTube, shared here with thanks; we are not connected to the channel. Open on YouTube(opens in a new tab)

How to remove wallpaper glue from walls

Taking the paper down is only half the job, because a film of old paste stays on the wall. Leave it there and new paint can crack or peel over it, and new paper can fail to bond. This Old House's guide is blunt about it: leftover glue can discolour and peel new paint. Re-wet a section of about a metre, scrape with a wide knife, scrub with a non-scratch dish pad and wipe with a rag soaked in clean water until the wall no longer feels slippery, then wash each section with warm water and a sponge from top to bottom.

Change the rinse water often, since dirty water simply spreads the paste around again. To check that it is all gone, the same guide suggests spraying the wall with a mix of one quart of water and one ounce of povidone-iodine, the antiseptic found in pharmacies; any remaining adhesive turns purple and can be cleaned off or sanded lightly. Then let the wall dry for a full day, longer in a humid room, before it is primed.

Can you wallpaper over paint, old wallpaper, tiles or texture?

Over sound paint, yes. Chelsea Textiles, a British fabric and wallpaper house, asks for painted surfaces to be sanded to roughen them, so the paste has something to grip, and for flaking or powdery areas to be scraped off first. Gloss and silk paints are slippery and need a thorough key before anything sticks to them. Fresh paint needs time as well: one maker of peel-and-stick paper asks for four to six weeks before its product goes on, and a pasted paper over paint that is still curing can lift in the same way.

Over old wallpaper, almost never. The old layer softens under fresh paste and can let go, taking the new paper with it, and its seams and edges show through. Over tiles, not as a lasting finish: the joints show, the glaze offers no grip and kitchens and bathrooms are the wrong place for paper anyway. Over a textured wall, only after the texture has been dealt with, as the next sections explain.

What each wall needs before it is papered

  • Sound matt or eggshell paint

    What it needs first
    Clean, light sanding, primer to suit the paper
  • Gloss or silk paint

    What it needs first
    A thorough key (sanding), then primer
  • Flaking or powdery paint

    What it needs first
    Scraped back to a firm edge, filled, primed
  • Old wallpaper

    What it needs first
    Stripped, glue washed off, repaired, primed
  • Textured paint or plaster

    What it needs first
    Skim coat, or a heavy lining paper
  • New plaster or new gypsum board

    What it needs first
    Fully dry, then sealed or sized
  • Damp stain or soft plaster

    What it needs first
    Cause found and fixed, wall dried, then repaired
  • Tiles

    What it needs first
    Not papered; removed or covered with a board first

General guidance. Your chosen paper's own instructions take priority.

Part of a trade decorating series from the group behind Sanderson and Morris & Co: how a glossy surface is keyed and a wall is sized before hanging, in under three minutes. Video by Highclere Interiors on YouTube, shared here with thanks; we are not connected to the channel. Open on YouTube(opens in a new tab)

Cracks, holes and putty

Fine cracks are opened slightly with a scraper so the filler can grip the sides rather than sit on the surface, then filled, left to harden and sanded flush. Holes from old curtain brackets, picture hooks and wall plugs get the same treatment. The finish of each repair matters as much as the filling: a patch that stands a millimetre proud of the wall turns into a shallow bump under a smooth paper, especially in low light.

Putty, the fine filler our team uses for dents and small defects, is ideal for local repairs. A crack that reappears in the same place after filling, or one that runs diagonally from the corner of a door or window, may mean the wall is moving. We point those out before work starts, so the building can be checked first if needed, rather than hiding a problem under fresh paper.

Bedroom wall finished in a textured cream plaster crossed by straight gold-look strips at different angles, behind an upholstered headboard of offset pads
From our project library: a textured plaster finish with gold strips. A raised texture like this has to be skimmed flat before a smooth paper could go over it.

Textured walls: skim coat or lining paper

Many UAE apartments are finished with a light sprayed or rolled texture, and it is the most common reason a smooth paper looks wrong after hanging. Every peak of the texture pushes up under the paper and catches the light. Filling it spot by spot does not work; the wall needs one flat face.

There are two ways to get it. A skim coat is a thin layer of finishing plaster or putty spread over the whole wall and sanded smooth once dry; it gives the best surface and suits walls that will be papered for years. A heavy lining paper, hung first and left to dry, bridges a light texture and small cracks and gives the decorative paper an even base; Chelsea Textiles recommends cross-lining, hanging the lining horizontally, so its joins never sit under the joins of the paper above. A skim takes longer because it has to dry, and it appears on the quotation as its own line.

Damp: fix the cause before anything else

Wallpaper does not cure damp. It hides it for a few weeks and then shows it, with bubbles, opening seams, brown tidemarks and, behind the paper, mould. If the inspection finds a stain or a soft patch, the source comes first: a leaking pipe, a split AC unit dripping into the wall, a failed seal around a window or a bathroom that is not ventilated. After the repair, the plaster must dry right through, which can take weeks, before preparation starts again.

In air-conditioned homes there is a quieter cause as well. An outside wall cooled hard by the AC can sit below the temperature at which the moist air in the room condenses, so it stays damp without any leak. How that works, and what it means for the choice of paper and paste, is explained in wallpaper in humid, air-conditioned rooms.

Long majlis with plain white walls and a split air conditioner mounted high on one wall, above low off-white seating on dark carved frames and hexagonal carved tables
From our project library: a majlis with a split AC unit high on the wall. The plaster around and below such units is one of the first places we check for moisture.

New plaster, fresh paint and gypsum board

New plaster has to be completely dry before it is papered, as every maker's instructions say, and in a new villa or after a renovation that can mean weeks. It is also very absorbent: unsealed, it drinks the paste unevenly, so the paper bonds in some places and not in others. Chelsea Textiles asks for absorbent surfaces to be sealed with a primer and left to dry fully before hanging.

Gypsum board partitions need sealing for a further reason. Paper pasted straight onto the board's paper face bonds to it so well that, years later, stripping the wallpaper can tear the board's face away with it. A primer or sealer first keeps the next redecoration simple. On any newly built or newly repaired wall, it is worth fixing the hanging date only after the wall has been checked for dryness.

Primer, size and the right paste

A primer or size evens out how much the wall absorbs, so the paste dries at the same rate everywhere and each length can still be slid into position while the pattern is matched. Which one is right depends on the paper. Chelsea Textiles, for instance, warns that metallic effects can be affected by an alkaline wall and asks for an alkaline-resistant primer there, and it tells hangers to paste the wall rather than the paper, using a pH-neutral, solvent-free paste with a fungicide.

Because the right products follow the paper, we take them from the instructions of the paper you have chosen rather than using one method for everything. Before the first cut, every roll is checked for the same batch number and shade, and after two or three lengths are up the work is checked again in the room's own light.

Sockets, edges and the order of work

The paper is trimmed along the ceiling line, the skirting and the door frames, and around every switch and socket, so those edges must be sound too. Crumbling plaster at the ceiling line or a gap beside a frame shows the moment the paper is up. If a socket or switch needs to move, move it before the wall is prepared, not after; our team handles small electrical work of that kind in-house, which keeps the sequence simple. On a typical room, the order runs like this:

  • Agree at the free visit what each wall needs, and price it
  • Move sockets or switches if the layout needs it
  • Strip old wallpaper, wash off the glue, scrape loose paint
  • Fill cracks and holes; skim or line textured walls
  • Sand, clean off the dust and let every repair dry
  • Prime or size to suit the chosen paper
  • Check rolls for batch and shade, then hang

Who prepares the wall, and what it costs

With us, the same team prepares the wall and hangs the paper, so there is never a question afterwards of whether a lifting seam was the wall's fault or the hanger's. Routine filling and putty are part of our supply-and-install rate, which starts at AED 45 per m² of wall. Work beyond that, such as a full skim coat, stripping old paper, or repairs after damp, is listed as its own line on the quotation, so you can see exactly what each wall needs before agreeing. Once the walls are ready and the rolls are in hand, a typical room is hung in about a day.

Our hanging carries a 24-month written workmanship warranty, and supplied papers follow their makers' terms. To plan a room, see our wallpaper service or wallpaper in Sharjah; room-by-room figures are in the wallpaper price guide, and the number of rolls is worked out in how many rolls of wallpaper you need.

Common questions

  • How do you prepare a wall for wallpaper?

    Inspect it, strip old paper and loose paint, fill cracks, skim or line any texture, let repairs dry, then prime or size as the paper asks. Preparing walls for wallpaper.

  • How do you remove wallpaper without a steamer?

    Peel off what comes dry, score the rest lightly, then soak it with warm water and a stripper and scrape it away as it softens. Removing old wallpaper.

  • How do you get wallpaper glue off the walls?

    Re-wet small sections, scrape, scrub with a non-scratch pad and rinse with clean water until the wall stops feeling slippery. Let it dry for a day. Removing wallpaper glue.

  • Can wallpaper go on painted walls?

    Yes, on sound paint that has been cleaned and lightly sanded, with the primer the paper asks for. Flaking or powdery paint must come off first. Papering over paint.

  • Why is my new wallpaper bubbling or peeling?

    Usually moisture in the wall, a dusty or powdery surface, or the wrong paste for the paper. The fix depends on the cause. Wallpaper, AC and humidity. Other faults are covered in wallpaper problems and fixes.

  • Is wall preparation included in the wallpaper price?

    Routine filling and putty are. A full skim, stripping old paper or repair after damp is quoted as a separate line. Wallpaper price, room by room.

Sources & specifications

Manufacturer information applies to the named products and systems. Sources reviewed on 28 October 2026.

  1. Chelsea Textiles: wallpaper hanging instructions (preparation, sanding paint, sealing, cross-lining, primer, paste)chelseatextiles.com(opens in a new tab)
  2. This Old House: how to strip wallpaper (scoring, soaking, scraping, washing off adhesive, residue test)thisoldhouse.com(opens in a new tab)
  3. MEINEWAND help centre: removal symbols (dry strippable, peelable, wet removal)support.meinewand.com(opens in a new tab)
  4. Bien Fait Paris: curing time for freshly painted walls before peel-and-stickbien-fait-paris.com(opens in a new tab)

Want this planned for your home?

Consultation and measurement are free. Tell us the rooms, location and what you need; we arrange a sample visit and define the measured quotation.

Services this article applies to

Wallpaper Supply & Installation made by Al Tareeq Decor

Wallpaper Supply & Installation

From AED 45 per sqm

The service behind this guide

Wallpaper Supply & Installation

Textured vinyl, fabric wallcoverings and 3D wall finishes, fitted seamlessly.

From AED 45 per sqmInstalled once your paper is in hand; a typical room takes about a day, and catalogue papers already in stock arrive soonest.
  • Heavyweight washable, scrub-resistant vinyl
  • Breathable non-woven backing with anti-mould protection
  • Wall preparation by our own team, including crack filling and putty
  • Odourless, anti-bacterial European adhesives
Get a Free Quote on WhatsApp