Skip to main content

Wallpaper · 14 min read · 18 June 2026

How to remove old wallpaper and wallpaper glue from a wall

Peel off what comes dry, spray the rest and wait 10 to 15 minutes, scrape with a plastic blade, then wash the paste off until the wall feels chalky. Let it dry a day before paint or new paper.

By Ali Haider Basra, Founder, Al Tareeq Decor · Contact our workshop

Spacious room with plain smooth white walls, a wall-mounted air conditioner and a glossy white floor, holding a long cream-cushioned majlis seat on dark carved wood frames with hexagonal tables

Key takeaways

  • Test a corner first: paper that peels dry is strippable; paper that splits leaves a backing; the rest comes off wet.
  • Wet one square metre at a time with hot water and vinegar or a stripper, wait 10 to 15 minutes, then scrape with a plastic blade held nearly flat.
  • Gypsum board has a paper face: use the least water that works, skip deep scoring and never use a metal scraper hard.
  • Wash off all the paste before anything else goes on; the wall should feel chalky, not slippery, then dry for about a day.
  • Our team strips old paper and mends the wall as its own quotation line, then hangs new paper from AED 45 per m², supplied and fitted.
On this page

How to remove wallpaper and wallpaper glue: the short answer

Peel off whatever comes away dry, wet the rest with hot water and a little white vinegar (or a wallpaper stripper), wait 10 to 15 minutes and lift it with a wide plastic scraper held nearly flat to the wall. Then wash the leftover paste off in small patches until the bare wall feels dull and chalky under your palm rather than slippery, and leave it about a day to dry out before paint, filler or new paper goes on.

That is the whole job, and the details decide whether it takes an afternoon or ruins a wall. The drawing below follows one slice of wall through the five stages: spray, wait, scrape, wipe and the hand test. Notice how the wet-time clock and the glue's grip move together, because patience in the second stage is what makes the third one easy.

This guide stays on the removal itself. Once the wall is bare, filling cracks, skimming, priming and choosing paper all have their own place in our guide to preparing walls for wallpaper.

A wall in cross-section as old wallpaper is wetted, scraped and wiped, with a wet-time clock and the glue's grip fallingCross-section of a wall, its layer of paste and the paper on top, shown through five stages: the paper is sprayed, a wet-time clock counts up to 15 minutes while the paste softens and its grip falls, a scraper lifts the paper in a strip, a sponge wipes away the thin film of paste, and a hand test finds the wall chalky rather than slipperyRemoving wallpaper and its glueCross-section: wall, paste, paper. Not to scale.Clean, ready to dryWallGluePaperWet time15min051015Glue grip0%SprayWaitScrapeWipeHand test — chalky, not slipperyWaits: 5–10 min and 10–15 min per two guides. Grip bar is an illustration.12345
  1. 1. Spray: hot water with vinegar or a stripper, one section at a time
  2. 2. Wait: 10–15 minutes while the paste softens and the paper darkens
  3. 3. Scrape: lift the paper in strips with a wide plastic scraper held low
  4. 4. Wipe: sponge off the thin film of paste, then rinse with clean water
  5. 5. Hand test: the wall should feel chalky and dull, never slippery
Our drawing of the five stages of removing wallpaper and glue. The waits come from two published guides; the grip bar illustrates the idea and is not a measurement.

First, find out which kind of wallpaper is on your wall

Wallpaper comes off in one of three ways, and the first ten minutes of the job should be spent learning which. Pick a corner beside a seam, ideally somewhere hidden, and ease the edge up with a plastic putty knife until you can take hold of it. Then draw it towards the floor, keeping the strip close to the wall. A full sheet that comes away dry and clean is strippable paper, and most of the work is already done. A printed face that lifts while a thin paper backing stays stuck behind it is splittable paper, a common trait of vinyl. Paper that will not lift, or breaks into scraps, has to come off wet.

Manufacturers print this on the roll with symbols. The wallpaper seller MEINEWAND explains three of them: removable without residue, which comes off dry; a paper that can be split, where only the upper layer peels off dry and the lower one stays; and a paper that must be removed wet. Nobody keeps the roll label for years, so the corner test is your answer.

The splittable type needs one extra decision. A backing that stays flat, firm and unbroken is sometimes kept in place as the base for new paper. One that blisters or lifts anywhere has to go as well, by the wet method below. How papers are built, and why that decides how easily they come off, is explained in our guide to choosing wallpaper for each room. The video below shows all three types being removed, side by side.

What the corner test tells you

  • The whole sheet peels off dry

    Type of paper
    Strippable (removable)
    What to do
    Peel it in long strips; wash off the paste afterwards
  • Only the printed face peels; a backing stays

    Type of paper
    Splittable, often vinyl
    What to do
    Peel the face, then wet and scrape the backing
  • It will not lift, or tears into small pieces

    Type of paper
    Must be removed wet
    What to do
    Spray, wait, then scrape in sections
  • Water beads and runs off the surface

    Type of paper
    Vinyl face or painted-over paper
    What to do
    Break the surface lightly so water can get in

A general guide. Test in a hidden spot, such as behind a door or wardrobe, before opening up a visible wall.

A painting expert shows three kinds of paper, removable, strippable and vinyl, and how each one is taken off: prying a corner for the dry ones, and scoring plus a hot-water-and-vinegar spray for the stubborn ones. Video by This Old House on YouTube, shared here with thanks; we are not connected to the channel. Open on YouTube(opens in a new tab)

Do you need to score the wallpaper before wetting it?

Scoring means scratching tiny holes through the surface so water can reach the paste. It helps only when the surface blocks water. A quick way to find out is to mist a small patch: if the water soaks in within a minute, skip scoring altogether, which is what one painting contractor's guide advises. Paper that soaks up water does not need holes.

Vinyl is the usual case that does. Its plastic face repels the spray, so water runs down the wall and the paste underneath stays dry. This Old House's painter makes the same point on camera: the solution has to saturate a vinyl paper before it will let go. Use light pressure and small overlapping circles, because every deep score is a mark in the wall that you will have to fill later.

On gypsum board, be more careful still. Gypsum board, the plasterboard that lines most partitions, has a paper skin. Fine Homebuilding warns that a scarifying tool can perforate and scar it, and recommends keeping it as a last resort. On a board wall, peel the vinyl face first, when it splits, and wet the backing that is left, which takes water without any scoring.

What to wet it with, and how long to wait

You do not need much equipment. A pump sprayer or a spray bottle, a bucket, a sponge and a wide plastic scraper do most of the work, and a steamer is an optional extra for the worst layers. The main choice is the liquid, and the published options are close in effect and different in cost.

Whatever you choose, work in sections about a metre wide, the size one painting guide recommends, and keep to the clock. Too little time and you will be scraping dry paste; too much and the section dries out again, which means spraying a second time. Before wetting anything, switch off the circuit that feeds the room's outlets, take off the faceplates and cover the holes, because water runs down inside a wall. Fine Homebuilding suggests checking the circuit with a voltage tester. Lay towels or canvas on the floor rather than plastic sheeting, which turns slippery when wet, and move furniture away as set out in our guide to preparing an occupied home.

Wetting options and the waits published for them

  • Hot water and white vinegar

    How it is mixed
    Equal parts, in a spray bottle
    Published wait
    10–15 minutes (This Old House; TaskRabbit)
    Best for
    Most papers, the cheapest start
  • Fabric softener and warm water

    How it is mixed
    1 part to 3 parts water
    Published wait
    10–15 minutes (TaskRabbit)
    Best for
    A second try on stubborn paste
  • Wallpaper stripper

    How it is mixed
    Ready to use, or as the label directs
    Published wait
    5–10 minutes; 3–5 minutes on a leftover backing (Fine Homebuilding)
    Best for
    Vinyl, backings and thick paste
  • Steamer

    How it is mixed
    Held against the surface
    Published wait
    About 15 seconds to 2 minutes a spot, depending on the guide
    Best for
    Several layers or painted-over paper

Published figures from the guides in our sources; read the label of any product you buy. If a stripper dries on the wall before you scrape, spray it again.

Peel and scrape without hurting the wall

Begin at a seam or a top corner and lift the paper with the scraper's edge, then pull it down at a shallow angle, close to the wall, so the strip separates from the paste rather than tearing across. Use a wide plastic scraper, and keep the blade nearly flat. Fine Homebuilding recommends a plastic smoother-scraper and warns against metal-edged ones on gypsum board, which cut into the face. A scraper that digs in will leave a gouge, and every gouge is extra work with filler later.

Read what the paper is telling you. Coming away in long, soft strips means the wetting worked. Coming off in dry confetti means it needs more water or more time, not more force. When you reach a patch that resists, spray it again, wait a few minutes and try once more; do not chisel at it.

Rooms with split AC units dry the air quickly, so a section can go dry while you work on the next one. Keep a bucket of hot water close, and finish each section completely, paper and paste, before moving across. The paste should be washed off while it is still damp, and it is far easier to do that than to re-wet it hours later.

  • Spray a square metre, wait out the clock, then scrape before the next section.
  • Pull at a shallow angle with the blade nearly flat, never pointing at the wall.
  • Re-spray anything that resists; extra water is cheaper than a gouge.
  • Drop scraps into a bag as you go, because wet paper is slippery underfoot.
  • Stop and switch the power off again if water reaches a socket or switch plate.

Gypsum board, plaster or block: what each wall can take

The wall under the paper sets the limit on how much water, steam and force you can use. In UAE homes the usual backing is cement plaster over block, often with a thin putty skim and paint beneath the paper. Partitions and false walls are usually gypsum board, and a few older rooms have paper pasted straight onto bare plaster.

Plaster over block is the most forgiving. Fine Homebuilding notes that plaster tolerates more steaming and scraping than board does, though it still wants a test in a hidden spot first. A gypsum board wall is the delicate one: its paper face is easy to wet through, blister and tear, which then needs sealing and skimming before anything else goes up. If the paper was stuck to unsealed board, even careful work can pull the face off with it, and Fine Homebuilding says that in that case replacing the board, or covering it with a thin new layer, gives a better result than patching.

A different warning applies to a wall that is damp. If paper keeps lifting by itself at the foot of an outside wall, behind a bathroom or under an AC drain, the wall may be wet from behind. Removing the paper will not cure that, and new paper will fail again. Trace and stop the moisture first; our guide to wallpaper in humid climates explains where it comes from.

The wall under the paper decides the method

  • Cement plaster over block

    Water and steam
    Handles hot water; test steam first
    Tools
    Plastic scraper first; metal only if needed
    Watch for
    Old paint flaking away with the paper
  • Plaster with a thin putty skim

    Water and steam
    Light spraying, short waits
    Tools
    Plastic scraper only
    Watch for
    Skim lifting in patches
  • Gypsum board

    Water and steam
    As little water as will do the job
    Tools
    Plastic scraper, no scoring tool
    Watch for
    Torn paper face and blisters
  • Paper stuck on bare, unsealed board

    Water and steam
    Very little; peel dry where possible
    Tools
    Plastic scraper, slow work
    Watch for
    The face coming off with the paper
  • Damp or stained wall

    Water and steam
    Do not wet it more
    Tools
    Not yet
    Watch for
    A leak or condensation behind the wall

Our own summary of the guides in the sources. A professional can read a wall quickly; if in doubt, test a hidden spot.

Getting the old wallpaper glue off the wall

When the paper is gone, the wall is still covered with a film of paste, and this is the step people skip. Paint over it and the paste can discolour or lift the new coat; hang paper over it and the new paste meets old paste instead of a clean wall. Several painting guides say the same thing: take the glue off before anything else goes on, and do it before it has dried hard again.

Spray a patch of about a square metre with warm water and a little stripper or the vinegar mix, give it a few minutes, then lift the softened film with the flat scraper. Go over it with a soft nylon brush or a non-scratch pad, which is the tool Fine Homebuilding names for paste residue, and wipe with a sponge. Rinse with clean water, changing it often, because grubby water only paints the paste back across the wall. On gypsum board, wipe rather than flood.

Then check it by hand. A painter's guide gives a good test: once the wall has dried, run a bare hand over it. A clean wall feels chalky and dull. Any slick or tacky patch still has paste on it, so wash that area again. Rust-Oleum's wallpaper-removal instructions follow the same order for stubborn paste: re-apply the stripper, let it work, scrape and rinse. The short video below shows the washing step in under two minutes.

A quick demonstration of getting paste residue off a wall once the paper is down, so that paint can go on: the tips are about wetting and washing, not scraping harder. Video by Know How Now on YouTube, shared here with thanks; we are not connected to the channel. Open on YouTube(opens in a new tab)

Repairing the wall after the paper is off

Once the paste is gone and the wall is dry, look over it for damage. Small gouges and tears in a board's paper face need a thin coat of filler or joint compound, sanded flush once it has dried. A larger torn area is better handled by skimming a thin coat over the whole wall and sanding it flat, because a patchy repair can show through paint and paper alike. If the face has come away in sheets, the board may need replacing, as Fine Homebuilding advises.

Sweep a lamp along the wall at a low angle, from the side rather than head-on, so every ridge and dip throws a shadow. That shows what needs another pass, and it shows what will show through new paper. Old textured finishes need the same attention: a raised pattern under a smooth covering would be visible as a pattern, which is why our team skims them first, as described in our 3D and textured feature wall guide.

The video below shows a full skim after wallpaper removal on drywall, with tape repairs. Repair and priming in more depth, including cracks and moving walls, belong to the wall preparation guide.

Close view of a bedroom wall in raised cream plaster relief, with narrow gold-toned strips running across it in straight lines, above the padded headboard of a bed
From our project library: a raised plaster texture with gold strips. A surface like this must be flat before a smooth paper goes on, and it shows why bare walls are checked closely first.
A drywall finisher takes a wall that has just lost its wallpaper, seals it, repairs the corners and joints, and skims it smooth with joint compound. Video by Paul Peck DrywallTube on YouTube, shared here with thanks; we are not connected to the channel. Open on YouTube(opens in a new tab)

How long to wait before painting or hanging new paper

Drying time is where jobs go wrong, because a wall that looks dry can still be holding water. After washing off the paste, one painting guide asks for at least 24 hours before priming. In the UAE's humid weeks, or in a room with little AC, give it longer, and do not close a damp wall under primer.

What goes on next decides the rest. One painting contractor's guide seals a stripped wall with a single coat of stain-blocking primer, so that torn paper and any leftover paste do not show through, and prefers an oil-based or shellac type to a water-based one, since water can soften old paste again. If new paper is going on, ask whoever hangs it which primer or size they use. A size or wallpaper primer is worth having because it lets the next paper come off as a simple soak-and-peel when its turn comes.

Choosing between paint and paper for the bare wall is a separate decision, and we have a guide to wallpaper or paint for UAE homes. If paper is the choice, how much you need and what repeats cost is in wallpaper costs: quantity, pattern repeat and preparation.

A timetable for the bare wall

  • After wetting and scraping

    What to wait for
    Finish the paste wash before the wall dries hard
    Source or basis
    Our advice; paste is easier to move while damp
  • After washing off the paste

    What to wait for
    At least 24 hours before primer; longer in humid weather
    Source or basis
    A painting guide's 24 hours, plus our humidity allowance
  • After filler or a skim coat

    What to wait for
    Until fully dry and sanded, as the product label says
    Source or basis
    The label of the product you use
  • After primer

    What to wait for
    The primer's recoat time on its label
    Source or basis
    The label of the product you use
  • Before new paper

    What to wait for
    A dry, sound, clean wall, primed or sized
    Source or basis
    Our wall-preparation guide

Times depend on the product, the wall and the weather. The label always wins over a general guide.

What not to do when removing wallpaper

Most damage to walls comes from a short list of shortcuts, and every one of them feels reasonable at the time. These are the ones we would ask you to avoid.

  • Do not flood a gypsum board wall. Wet the paper, not the wall behind it.
  • Do not use a metal-edged scraper hard against board, and do not score a board wall deeply.
  • Do not paint or hang new paper over leftover paste, or over old wallpaper.
  • Do not leave power on to sockets and switches that water can reach.
  • Do not strip a wall that is damp from behind until the cause is found and fixed.
  • Do not wash with a pressure of water that runs under skirting and into joints.

Remove it yourself, or call a professional?

One small room of paper that peels dry is a reasonable weekend job. Call in a professional when there are several layers, a vinyl paper stuck to gypsum board, paper that has been painted over, tall ceilings or ceilings themselves, a whole villa, or any sign of damp. These are the jobs where the wall, not the paper, is the expensive thing to get wrong. Tenants should also read their lease, since many ask for walls to be handed back in their original condition.

Our team does remove old wallpaper. The old covering is stripped, and the wall is filled and puttied where it needs it, with both shown as their own line in the quotation so the cost is plain. We then hang new paper from a laser line with the pattern matched, from AED 45 per m² supplied and hung, or from AED 20 per m² to hang paper you bought yourself. A typical room takes about a day to prepare and paper once the paper is in hand, and our hanging work carries a 24-month written workmanship warranty. The wallpaper service page has the full list, and wallpaper price, room by room shows what a bedroom, a majlis or a corridor adds up to.

The measuring visit is free and the catalogues come with us, so you can hold the paper against the bare wall that the removal has uncovered. See local details for wallpaper in Sharjah and wallpaper in Dubai, or look at wallpaper installation and fixing and the wallpaper supply and collections. The pricing guide helps work out a budget before the visit, and a feature wall is covered in wallpaper feature wall planning.

Bedroom with a large veined stone-pattern wallcovering in grey and cream rising above a grey buttoned leather headboard, and an oval mirror in a fluted white recess beside it
From our project library: a marble-look paper on the bedhead wall. New paper looks as good as the bare wall under it, which is why removal and preparation come first in our quotation.

Common questions

  • How do I remove old wallpaper glue from walls?

    Re-wet a square metre with warm water and a little stripper or vinegar, wait a few minutes, scrape flat and scrub with a soft nylon pad. Rinse until the dry wall feels dull and powdery, not slick. Preparing walls for wallpaper.

  • Do I have to remove wallpaper glue before painting?

    Yes. Leftover paste can discolour or lift new paint, so wash it off and let the wall dry for about a day before priming. Wallpaper or paint for UAE homes.

  • How long should wallpaper soak before I scrape it?

    Strippers are usually left 5 to 10 minutes; hot water with vinegar 10 to 15. Spray again if the section dries before you reach it. Wall preparation guide.

  • How do I remove wallpaper from a gypsum board wall?

    Use the least water that works, a plastic scraper and no deep scoring, because the board's face is paper. Peel a vinyl face first, then wet the backing. Wallpaper in humid climates.

  • Can I put new wallpaper over old wallpaper?

    Almost never. Fresh paste softens the old layer and its seams show through, so strip it, clean the wall and prime it first. Choosing wallpaper for each room.

  • Does Al Tareeq Decor remove old wallpaper in Sharjah and Dubai?

    Yes. Our team strips the old covering and fills and putties the wall, shown as its own line in the quotation, then hangs the new paper. Wallpaper in Sharjah.

  • How much does it cost to remove wallpaper in the UAE?

    Removal is quoted as its own line after our free visit, because it depends on the layers and the wall. New paper starts from AED 45 per m², supplied and fitted. Wallpaper price, room by room.

Sources & specifications

Manufacturer information applies to the named products and systems. Sources reviewed on 29 October 2026.

  1. Fine Homebuilding: stripping wallpaper (corner test, solutions, soak times, plastic scrapers, drywall face damage)finehomebuilding.com(opens in a new tab)
  2. Composite Paint: wallpaper removal (misting test for scoring, paste residue, hand test, drying and primer)compositepaint.com(opens in a new tab)
  3. Rust-Oleum Canada: wallpaper removal tips (stripper, dwell, scraping and re-treating adhesive)rustoleum.ca(opens in a new tab)
  4. MEINEWAND help centre: what the wallpaper symbols mean (removal symbols)support.meinewand.com(opens in a new tab)
  5. TaskRabbit: how to remove wallpaper (vinegar and fabric-softener mixes, soak time)taskrabbit.com(opens in a new tab)

Want this planned for your home?

Consultation and measurement are free. Tell us the rooms, location and what you need; we arrange a sample visit and define the measured quotation.

Services this article applies to

Wallpaper Supply & Installation made by Al Tareeq Decor

Wallpaper Supply & Installation

From AED 45 per sqm

The service behind this guide

Wallpaper Supply & Installation

Textured vinyl, fabric wallcoverings and 3D wall finishes, fitted seamlessly.

From AED 45 per sqmInstalled once your paper is in hand; a typical room takes about a day, and catalogue papers already in stock arrive soonest.
  • Heavyweight washable, scrub-resistant vinyl
  • Breathable non-woven backing with anti-mould protection
  • Wall preparation by our own team, including crack filling and putty
  • Odourless, anti-bacterial European adhesives
Get a Free Quote on WhatsApp